Features and benefits
- Wendeschneidplatten mit PKD Schneidensegment zur Bearbeitung von NE-Werkstoffen.
- Hohe Verschleißfestigkeit und längere Standzeit.
- Gesteigerte Produktivität dank hoher Vorschübe.
Maschinenseite
loading...
Werkstückseite
loading...
WARNUNG • Drill Fix DFR
WARNING During through-hole operations, a slug or disc is produced as the tool breaks through the workpiece. When the drill is stationary and the workpiece is rotating, this slug may be hurled from the chuck by centrifugal force. Provide adequate shielding to protect bystanders. |
D | LS | CS |
32 | 58 | R 1/4 BSP |
40 | 68 | R 1/4 BSP |
50 | 68 | R 1/4 BSP |
DFT™ • PKD • Metrisch
Metric | |||||||||||||||
Material
|
Condition | Pocket Seat | Geometry | Grade | Cutting Speed
|
Recommended Feed Rate (f) by Diameter | |||||||||
Range
|
|||||||||||||||
Min | Starting Value | Max | Ø | DFT03 16
|
DFT05 25
|
DFT06 33
|
DFT07 41
|
DFT09 49
|
DFT11 69
|
||||||
N | 1 | S | O | ST/C | KD1425 | 480 | 720 | 864 | mm/r | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 |
I | ST/C | KD1425 | |||||||||||||
2 | S | O | ST/C | KD1425 | 447 | 670 | 804 | mm/r | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
I | ST/C | KD1425 | |||||||||||||
3 | S | O | ST/C | KD1425 | 413 | 619 | 743 | mm/r | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
I | ST/C | KD1425 | |||||||||||||
4 | S | O | ST/C | KD1425 | 447 | 670 | 804 | mm/r | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
I | ST/C | KD1425 | |||||||||||||
5 | S | O | ST/C | KD1425 | 480 | 720 | 864 | mm/r | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
I | ST/C | KD1425 |
Inch | |||||||||||||||
Material
|
Condition | Pocket Seat | Geometry | Grade | Cutting Speed
|
Recommended Feed Rate (f) by Diameter | |||||||||
Range
|
|||||||||||||||
Min | Starting Value | Max | Ø | DFT03 .625–.969" | DFT05 .984–1.250" | DFT06 1.313–1.563" | DFT07 1.625–1.875" | DFT09 1.938–2.125" | DFT11 2.750–3.250" | ||||||
N | 1 | S | O | ST/C | KD1425 | 1575 | 2362 | 2834 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 |
I | ST/C | KD1425 | |||||||||||||
2 | S | O | ST/C | KD1425 | 1465 | 2197 | 2636 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
I | ST/C | KD1425 | |||||||||||||
3 | S | O | ST/C | KD1425 | 1355 | 2032 | 2438 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
I | ST/C | KD1425 | |||||||||||||
4 | S | O | ST/C | KD1425 | 1465 | 2197 | 2636 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
I | ST/C | KD1425 | |||||||||||||
5 | S | O | ST/C | KD1425 | 1575 | 2362 | 2834 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
I | ST/C | KD1425 |
Metric | |||||||||||||||
Cutting Speed
|
|||||||||||||||
Range
|
Recommended Feed Rate (f) by Diameter | ||||||||||||||
Material
|
Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFT03 16
|
DFT05 25
|
DFT06 33
|
DFT07 41
|
DFT09 49
|
DFT11 69
|
|
N | 1 | S | O | ST/C | KD1425 | 480 | 720 | 864 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 |
1 | S | I | ST/C | KD1425 | 480 | 720 | 864 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
2 | S | O | ST/C | KD1425 | 447 | 670 | 804 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
2 | S | I | ST/C | KD1425 | 447 | 670 | 804 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
3 | S | O | ST/C | KD1425 | 413 | 619 | 743 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
3 | S | I | ST/C | KD1425 | 413 | 619 | 743 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
4 | S | O | ST/C | KD1425 | 447 | 670 | 804 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
4 | S | I | ST/C | KD1425 | 447 | 670 | 804 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
5 | S | O | ST/C | KD1425 | 480 | 720 | 864 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 | |
5 | S | I | ST/C | KD1425 | 480 | 720 | 864 | mm/omw | 0,05–0,07 | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | 0,14–0,18 | 0,14–0,18 |