HARVI™ Ultra 8X • Fraise hélicoïdale • CI10 • A Tenons • Métrique
HARVI™ Ultra 8X • Fraise hélicoïdale • IC10 • A Tenons
Uses and application
Usinage de poches
Fraisage de côté/avec épaulement : Bout plat
Fraisage de côté/avec épaulement : Léger chanfrein
Slotting: Shoulder Profiling
Slotting: Shoulder
Fraisage — 3 tailles
Fraisage — Arrosage interne
Workpiece Materials
P
Steel
M
Stainless Steel
S
High-Temp Alloys
Filters and Columns
Filters
Filters
Filters
View filters in
Metric
Inch
Workpiece Material
Workpiece Material
-
P Steel (3)
-
P0Low-Carbon Steels, Long Chipping C < .25%; <125 HB; <530 N/mm^2 UTS(3)
-
P1Low-Carbon Steels, Short Chipping C < .25%; <125 HB; <530 N/mm^2 UTS(3)
-
P2Medium and High Carbon Steels C < .25%; <220 HB; <25 HRC; >530 N/mm^2 UTS(3)
-
P3Alloy Steels & Tool Steels C > .25%; <330 HB; <35 HRC; 600-850 N/mm^2 UTS(3)
-
P4Alloy Steels & Tool Steels C > .25%; 350-420 HB; 35-43 HRC; 850-1400 N/mm^2 UTS(3)
-
P5Ferritic, Martensitic, and PH Stainless Steels <330 HB; <35 HRC; 600-900 N/mm^2 UTS(3)
-
P6High Strength Ferritic, Martensitic, and PH Stainless Steels 350-450 HB; 35-43 HRC; 900-2400 N/mm^2 UTS(3)
-
-
M Stainless Steel (3)
-
M1Austenitic Stainless Steel 130-200 HB; <600 N/mm^2 UTS(3)
-
M2High Strength Austenitic Stainless and Cast Stainless Steels 150-230 HB; <25 HRC; >600 N/mm^2 UTS(3)
-
M3Duplex Stainless Steel 135-275 HB; <30 HRC; 500-1200 N/mm^2 UTS(3)
-
-
S High-Temp Alloys (3)
-
S1Iron-Based, Heat-Resistant Alloys 160-260 HB; 25-48 HRC; 500-1200 N/mm^2 UTS(3)
-
S2Cobalt-Based, Heat-Resistant Alloys 250-450 HB; 25-48 HRC; 1000-1450 N/mm^2 UTS(3)
-
S3Nickel-Based, Heat Resistant Alloys 160-450 HB; <48 HRC; 600-1700 N/mm^2 UTS(3)
-
S4Titanium and Titanium Alloys 300-400 HB; 33-43 HRC; 900-1600 N/mm^2 UTS(3)
-
Applications
Applications
-
Face Milling (3)
-
Shoulder Milling (3)
-
-
Slot Milling (3)
-
Slot Square End (3)
Cutting Diameter
Cutting Diameter
-
1.968 in (2)
-
2.4803 in (1)
to
Cutting Diameter
Cutting Diameter
-
50.0 mm (2)
-
63.0 mm (1)
to
Cutting Length
Cutting Length
-
54.831 mm (1)
-
85.028 mm (1)
-
86.067 mm (1)
to
Cutting Length
Cutting Length
-
2.1587 in (1)
-
3.3476 in (1)
-
3.3885 in (1)
to
Reach
Reach
-
2.679 in (1)
-
3.858 in (1)
-
4.0553 in (1)
to
Reach
Reach
-
68.0 mm (1)
-
98.0 mm (1)
-
103.0 mm (1)
to
Number of Flutes
Number of Flutes
-
4 (2)
-
5 (1)
Cutting Edges Per Insert
Cutting Edges Per Insert
-
4.0 (3)
-
8.0 (3)
to
Corner Radius
Corner Radius
-
0.031 in (3)
-
0.062 in (3)
-
0.078 in (3)
-
0.094 in (3)
-
0.125 in (3)
to
Corner Radius
Corner Radius
-
0.8 mm (3)
-
1.59 mm (3)
-
1.98 mm (3)
-
2.4 mm (3)
-
3.18 mm (3)
to
application
Grade Of Cutting Tool
Grade Of Cutting Tool
-
KC725M (3)
-
KCSM40 (3)
backEnd
Back-End Diameter
Back-End Diameter
-
22.0 mm (2)
-
27.0 mm (1)
to
Back-End Diameter
Back-End Diameter
-
0.8666 in (2)
-
1.063 in (1)
to
No filters matching ""
Change the visible columns with any of the parameters listed below. A maximum of 7 columns can be displayed.
Displaying
1- 3
of 3 results
Metric
Inch
Show
Metric
Inch
| SAP Material Number | ISO Catalog Number | ANSI Catalog Number | [D1] Effective Cutting Diameter | [D1] Effective Cutting Diameter | [D] Adapter / Shank / Bore Diameter | [D] Adapter / Shank / Bore Diameter | [D6] Hub Diameter | [D6] Hub Diameter | [L] Overall Length | [L] Overall Length | [AP1MAX] 1st Maximum Cutting Depth | [AP1MAX] 1st Maximum Cutting Depth | Number of Inserts | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 6523849 | HU8X050S10S22ZU4AP54Z28 | HU8X050S10S22ZU4AP54Z28 | 50.0000 | 1.968 | 22.0 | .8666 | 47.0700 | 1.853 | 68.0000 | 2.679 | 54.8310 | 2.158 | 28 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$2,561.71
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 6523850 | HU8X050S10S22ZU4AP84Z44 | HU8X050S10S22ZU4AP84Z44 | 50.0000 | 1.968 | 22.0 | .8666 | 47.0700 | 1.853 | 98.0000 | 3.858 | 85.0280 | 3.347 | 44 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$4,025.55
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 6524711 | HU8X063S10S27ZU5AP86Z55 | HU8X063S10S27ZU5AP86Z55 | 63.0000 | 2.480 | 27.0 | 1.063 | 60.0000 | 2.362 | 103.0000 | 4.055 | 86.0670 | 3.388 | 55 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$4,380.74
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
List price:
Discount: %
Replacement
This item is not available
Replacement Product This item may be available through a distributor
Replacement Product This item may be available through a distributor
Qty
Sold in pkg. of
Grades
Guide de sélection des plaquettes
| Material Group | LightMachining | GeneralPurpose | HeavyMachining | |||
| (Light geometry) | (Strong geometry) | |||||
| wear resistance |  | toughness | ||||
| Geometry | Grade | Geometry | Grade | Geometry | Grade | |
| P1–P2 | ||||||
| P3–P4 | ||||||
| P5–P6 | .S..GDH | KCSM40 | .S..GDH | KCSM40 | .S..GDH | KCSM40 |
| M1–M2 | .S..GDH | KCSM40 | .S..GDH | KCSM40 | .S..GDH | KCSM40 |
| M3 | .S..GDH | KCSM40 | .S..GDH | KCSM40 | .S..GDH | KCSM40 |
| K1–K2 | ||||||
| K3 | ||||||
| N1–N2 | ||||||
| N3 | ||||||
| S1–S2 | .S..GDH | KCSM40 | .S..GDH | KCSM40 | .S..GDH | KCSM40 |
| S3 | .S..GDH | KCSM40 | .S..GDH | KCSM40 | .S..GDH | KCSM40 |
| S4 | .S..GDH | KCSM40 | .S..GDH | KCSM40 | .S..GDH | KCSM40 |
| H1 | ||||||
Avances de départ recommandées [mm]
| Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | |||||||||||||||||
| Material | Insert Geometry | 5% | 10% | 20% | 30% | 40–100% | Insert Geometry | ||||||||||
| P5 | .S..GDH | – | – | – | 0,18 | 0,26 | 0,40 | 0,16 | 0,23 | 0,36 | 0,13 | 0,19 | 0,29 | 0,07 | 0,10 | 0,16 | .S..GDH |
| P6 | .S..GDH | – | – | – | 0,18 | 0,21 | 0,33 | 0,16 | 0,19 | 0,29 | 0,13 | 0,15 | 0,24 | 0,07 | 0,08 | 0,13 | .S..GDH |
| M1 | .S..GDH | – | – | – | 0,18 | 0,24 | 0,38 | 0,16 | 0,22 | 0,34 | 0,13 | 0,18 | 0,27 | 0,07 | 0,10 | 0,15 | .S..GDH |
| M2 | .S..GDH | – | – | – | 0,18 | 0,24 | 0,38 | 0,16 | 0,22 | 0,34 | 0,13 | 0,18 | 0,27 | 0,07 | 0,10 | 0,15 | .S..GDH |
| M3 | .S..GDH | – | – | – | 0,18 | 0,21 | 0,33 | 0,16 | 0,19 | 0,29 | 0,13 | 0,15 | 0,24 | 0,07 | 0,08 | 0,13 | .S..GDH |
| S1 | .S..GDH | – | – | – | 0,18 | 0,16 | 0,25 | 0,16 | 0,15 | 0,22 | 0,13 | 0,12 | 0,18 | 0,07 | 0,07 | 0,10 | .S..GDH |
| S2 | .S..GDH | – | – | – | 0,18 | 0,16 | 0,25 | 0,16 | 0,15 | 0,22 | 0,13 | 0,12 | 0,18 | 0,07 | 0,07 | 0,10 | .S..GDH |
| S3 | .S..GDH | – | – | – | 0,18 | 0,21 | 0,33 | 0,16 | 0,19 | 0,29 | 0,13 | 0,15 | 0,24 | 0,07 | 0,08 | 0,13 | .S..GDH |
| S4 | .S..GDH | – | – | – | 0,18 | 0,24 | 0,38 | 0,16 | 0,22 | 0,34 | 0,13 | 0,18 | 0,27 | 0,07 | 0,10 | 0,15 | .S..GDH |
| LightMachining | GeneralPurpose | HeavyMachining |
Avances de départ recommandées [mm]
| Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | |||||||||||||||||
| Material | Insert Geometry | 5% | 10% | 20% | 30% | 40–100% | Insert Geometry | ||||||||||
| P5 | .S..GDH | – | – | – | 0,18 | 0,29 | 0,45 | 0,16 | 0,26 | 0,40 | 0,13 | 0,21 | 0,33 | 0,07 | 0,12 | 0,18 | .S..GDH |
| P6 | .S..GDH | – | – | – | 0,18 | 0,24 | 0,38 | 0,16 | 0,22 | 0,34 | 0,13 | 0,18 | 0,27 | 0,07 | 0,10 | 0,15 | .S..GDH |
| M1 | .S..GDH | – | – | – | 0,18 | 0,28 | 0,43 | 0,16 | 0,25 | 0,38 | 0,13 | 0,20 | 0,31 | 0,07 | 0,11 | 0,17 | .S..GDH |
| M2 | .S..GDH | – | – | – | 0,18 | 0,28 | 0,43 | 0,16 | 0,25 | 0,38 | 0,13 | 0,20 | 0,31 | 0,07 | 0,11 | 0,17 | .S..GDH |
| M3 | .S..GDH | – | – | – | 0,18 | 0,24 | 0,38 | 0,16 | 0,22 | 0,34 | 0,13 | 0,18 | 0,27 | 0,07 | 0,10 | 0,15 | .S..GDH |
| S1 | .S..GDH | – | – | – | 0,18 | 0,20 | 0,30 | 0,16 | 0,17 | 0,27 | 0,13 | 0,14 | 0,22 | 0,07 | 0,08 | 0,12 | .S..GDH |
| S2 | .S..GDH | – | – | – | 0,18 | 0,20 | 0,30 | 0,16 | 0,17 | 0,27 | 0,13 | 0,14 | 0,22 | 0,07 | 0,08 | 0,12 | .S..GDH |
| S3 | .S..GDH | – | – | – | 0,18 | 0,23 | 0,35 | 0,16 | 0,20 | 0,31 | 0,13 | 0,17 | 0,26 | 0,07 | 0,09 | 0,14 | .S..GDH |
| S4 | .S..GDH | – | – | – | 0,18 | 0,28 | 0,43 | 0,16 | 0,25 | 0,38 | 0,13 | 0,20 | 0,31 | 0,07 | 0,11 | 0,17 | .S..GDH |
| LightMachining | GeneralPurpose | HeavyMachining |
Recommended Starting Feeds [IPT]
| Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | |||||||||||||||||
| Material | Insert Geometry | 5% | 10% | 20% | 30% | 40–100% | Insert Geometry | ||||||||||
| P5 | .S..GDH | – | – | – | .007 | .010 | .016 | .006 | .009 | .014 | .005 | .007 | .012 | .003 | .004 | .006 | .S..GDH |
| P6 | .S..GDH | – | – | – | .007 | .008 | .013 | .006 | .007 | .011 | .005 | .006 | .009 | .003 | .003 | .005 | .S..GDH |
| M1 | .S..GDH | – | – | – | .007 | .010 | .015 | .006 | .009 | .013 | .005 | .007 | .011 | .003 | .004 | .006 | .S..GDH |
| M2 | .S..GDH | – | – | – | .007 | .010 | .015 | .006 | .009 | .013 | .005 | .007 | .011 | .003 | .004 | .006 | .S..GDH |
| M3 | .S..GDH | – | – | – | .007 | .008 | .013 | .006 | .007 | .011 | .005 | .006 | .009 | .003 | .003 | .005 | .S..GDH |
| S1 | .S..GDH | – | – | – | .007 | .006 | .010 | .006 | .006 | .009 | .005 | .005 | .007 | .003 | .003 | .004 | .S..GDH |
| S2 | .S..GDH | – | – | – | .007 | .006 | .010 | .006 | .006 | .009 | .005 | .005 | .007 | .003 | .003 | .004 | .S..GDH |
| S3 | .S..GDH | – | – | – | .007 | .008 | .013 | .006 | .007 | .011 | .005 | .006 | .009 | .003 | .003 | .005 | .S..GDH |
| S4 | .S..GDH | – | – | – | .007 | .010 | .015 | .006 | .009 | .013 | .005 | .007 | .011 | .003 | .004 | .006 | .S..GDH |
| LightMachining | GeneralPurpose | HeavyMachining |
Recommended Starting Feeds [IPT]
| Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | |||||||||||||||||
| Material | Insert Geometry | 5% | 10% | 20% | 30% | 40–100% | Insert Geometry | ||||||||||
| P5 | .S..GDH | – | – | – | .007 | .012 | .018 | .006 | .010 | .016 | .005 | .008 | .013 | .003 | .005 | .007 | .S..GDH |
| P6 | .S..GDH | – | – | – | .007 | .010 | .015 | .006 | .009 | .013 | .005 | .007 | .011 | .003 | .004 | .006 | .S..GDH |
| M1 | .S..GDH | – | – | – | .007 | .011 | .017 | .006 | .010 | .015 | .005 | .008 | .012 | .003 | .004 | .007 | .S..GDH |
| M2 | .S..GDH | – | – | – | .007 | .011 | .017 | .006 | .010 | .015 | .005 | .008 | .012 | .003 | .004 | .007 | .S..GDH |
| M3 | .S..GDH | – | – | – | .007 | .010 | .015 | .006 | .009 | .013 | .005 | .007 | .011 | .003 | .004 | .006 | .S..GDH |
| S1 | .S..GDH | – | – | – | .007 | .008 | .012 | .006 | .007 | .011 | .005 | .006 | .009 | .003 | .003 | .005 | .S..GDH |
| S2 | .S..GDH | – | – | – | .007 | .008 | .012 | .006 | .007 | .011 | .005 | .006 | .009 | .003 | .003 | .005 | .S..GDH |
| S3 | .S..GDH | – | – | – | .007 | .009 | .014 | .006 | .008 | .012 | .005 | .007 | .010 | .003 | .004 | .006 | .S..GDH |
| S4 | .S..GDH | – | – | – | .007 | .011 | .017 | .006 | .010 | .015 | .005 | .008 | .012 | .003 | .004 | .007 | .S..GDH |
| LightMachining | GeneralPurpose | HeavyMachining |
Vitesses de départ recommandées [m/mn]
| Material Group | KC725M | KCSM40 | |||||
| P | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| 4 | |||||||
| 5 | 120 | 110 | 95 | 250 | 138 | 125 | |
| 6 | 105 | 80 | 65 | 225 | 127 | 115 | |
| M | 1 | 135 | 120 | 110 | 270 | 127 | 115 |
| 2 | 125 | 105 | 90 | 270 | 127 | 115 | |
| 3 | 90 | 80 | 65 | 200 | 88 | 80 | |
| K | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| N | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| S | 1 | 30 | 25 | 20 | 60 | 25 | 23 |
| 2 | 30 | 25 | 20 | 50 | 23 | 21 | |
| 3 | 35 | 30 | 20 | 55 | 26 | 24 | |
| 4 | 45 | 35 | 25 | 80 | 39 | 35 | |
| H | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
Vitesses de départ recommandées [m/mn]
| Material Group | KC725M | KCSM40 | |||||
| P | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| 4 | |||||||
| 5 | 120 | 110 | 95 | 250 | 138 | 125 | |
| 6 | 105 | 80 | 65 | 225 | 127 | 115 | |
| M | 1 | 135 | 120 | 110 | 270 | 127 | 115 |
| 2 | 125 | 105 | 90 | 270 | 127 | 115 | |
| 3 | 90 | 80 | 65 | 200 | 88 | 80 | |
| K | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| N | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| S | 1 | 30 | 25 | 20 | 60 | 25 | 23 |
| 2 | 30 | 25 | 20 | 50 | 23 | 21 | |
| 3 | 35 | 30 | 20 | 55 | 26 | 24 | |
| 4 | 45 | 35 | 25 | 80 | 39 | 35 | |
| H | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
Recommended Starting Speeds [SFM]
| Material Group | KC725M | KCSM40 | |||||
| P | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| 4 | |||||||
| 5 | 390 | 355 | 315 | 820 | 450 | 410 | |
| 6 | 340 | 265 | 210 | 740 | 415 | 375 | |
| M | 1 | 450 | 390 | 355 | 885 | 415 | 375 |
| 2 | 410 | 340 | 290 | 885 | 415 | 375 | |
| 3 | 300 | 265 | 210 | 655 | 290 | 260 | |
| K | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| N | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| S | 1 | 90 | 80 | 65 | 195 | 90 | 75 |
| 2 | 90 | 80 | 65 | 165 | 90 | 70 | |
| 3 | 120 | 90 | 65 | 180 | 105 | 80 | |
| 4 | 145 | 120 | 80 | 260 | 150 | 115 | |
| H | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
Recommended Starting Speeds [SFM]
| Material Group | KC725M | KCSM40 | |||||
| P | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| 4 | |||||||
| 5 | 390 | 355 | 315 | 820 | 450 | 410 | |
| 6 | 340 | 265 | 210 | 740 | 415 | 375 | |
| M | 1 | 450 | 390 | 355 | 885 | 415 | 375 |
| 2 | 410 | 340 | 290 | 885 | 415 | 375 | |
| 3 | 300 | 265 | 210 | 655 | 290 | 260 | |
| K | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| N | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
| S | 1 | 90 | 80 | 65 | 195 | 90 | 75 |
| 2 | 90 | 80 | 65 | 165 | 90 | 70 | |
| 3 | 120 | 90 | 65 | 180 | 105 | 80 | |
| 4 | 145 | 120 | 80 | 260 | 150 | 115 | |
| H | 1 | ||||||
| 2 | |||||||
| 3 | |||||||
Carrières
✉ Gardons le contact
© 2022 Terms & Conditions of Use | Conditions of Sale | Data Privacy Policy
Kennametal Inc. 525 William Penn Place Suite 3300, Pittsburgh, PA 15219
