Material Group | Light
|
General
|
Heavy
|
|||
– | (Light geometry) | – | (Strong geometry) | |||
– | wear
|
<="" td=""> | toughness | |||
– | Geometry | Grade | Geometry | Grade | Geometry | Grade |
P1–P2 | – | – | – | – | – | – |
P3–P4 | – | – | – | – | – | – |
P5–P6 | – | – | – | – | – | – |
M1–M2 | – | – | – | – | – | – |
M3 | – | – | – | – | – | – |
K1–K2 | – | – | – | – | – | – |
K3 | – | – | – | – | – | – |
N1–N2 | – | – | – | – | – | – |
N3 | – | – | – | – | – | – |
S1–S2 | .EGN | KYS30 | .EGN | KYS30 | .TGN | KYS30 |
S3 | .EGN | KYSP30 | .EGN | KYSP30 | .TGN | KYSP30 |
S4 | – | – | – | – | – | – |
H1 | – | – | – | – | – | – |
Przy osiowej głębokości skrawania (ap) 6,35
Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.EGN | 0,08 | 0,09 | 0,11 | 0,06 | 0,07 | 0,09 | 0,06 | 0,06 | 0,07 | 0,05 | 0,06 | 0,07 | 0,05 | 0,06 | 0,07 | .EGN |
.TGN | 0,13 | 0,17 | 0,19 | 0,09 | 0,13 | 0,14 | 0,08 | 0,11 | 0,13 | 0,08 | 0,10 | 0,12 | 0,08 | 0,10 | 0,12 | .TGN |
Przy osiowej głębokości skrawania (ap) 3,00
Light
|
General
|
Heavy
|
Przy osiowej głębokości skrawania (ap) 1,50
Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.EGN | 0,18 | 0,20 | 0,24 | 0,13 | 0,15 | 0,18 | 0,12 | 0,13 | 0,16 | 0,11 | 0,12 | 0,15 | 0,11 | 0,12 | 0,14 | .EGN |
.TGN | 0,27 | 0,36 | 0,41 | 0,20 | 0,27 | 0,31 | 0,17 | 0,23 | 0,27 | 0,16 | 0,22 | 0,25 | 0,16 | 0,21 | 0,24 | .TGN |
Przy osiowej głębokości skrawania (ap) 0,75
Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.EGN | 0,10 | 0,11 | 0,13 | 0,07 | 0,08 | 0,10 | 0,07 | 0,07 | 0,09 | 0,06 | 0,07 | 0,08 | 0,06 | 0,07 | 0,08 | .EGN |
.TGN | 0,15 | 0,20 | 0,23 | 0,11 | 0,15 | 0,17 | 0,10 | 0,13 | 0,15 | 0,09 | 0,12 | 0,14 | 0,09 | 0,12 | 0,14 | .TGN |
Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.EGN | 0,13 | 0,14 | 0,18 | 0,10 | 0,11 | 0,13 | 0,09 | 0,09 | 0,12 | 0,08 | 0,09 | 0,11 | 0,08 | 0,09 | 0,11 | .EGN |
.TGN | 0,19 | 0,26 | 0,30 | 0,15 | 0,19 | 0,22 | 0,13 | 0,17 | 0,19 | 0,12 | 0,16 | 0,18 | 0,12 | 0,15 | 0,18 | .TGN |
Poradnik montażu płytki
Safety Notes | |||||
<="" td=""> | <="" td=""> | <="" td=""> | <="" td=""> | <="" td=""> | <="" td="" /> |
Read all instructions carefully | Wear eye protection | Inspect and tighten fasteners regularly | Warning: Cutting hazard | Warning: Hot surfaces | Do not exceed maximum RPM |
Assembly Instructions | |
Assemble STCM-25 screw to KW1008 wedge, 1 to 1 1/2 turns. | Wedge/screw assembly. |
<="" td=""> | <="" td="" /> |
Install wedge/screw assembly into cutter body, but maintain assembly gap for installing insert. | Slide insert, RNGN12... into pocket and torque wedge/insert assembly to 3,5 Nm (31 in/lbs). Repeat for each pocket. |
<="" td=""> | <="" td="" /> |
Zalecane wyjściowe wartości prędkości skrawania [m/min]
Material Group | KYS30 | KYSP30 | |||||
P | 1 | – | – | – | – | – | – |
2 | – | – | – | – | – | – | |
3 | – | – | – | – | – | – | |
4 | – | – | – | – | – | – | |
5 | – | – | – | – | – | – | |
6 | – | – | – | – | – | – | |
M | 1 | – | – | – | – | – | – |
2 | – | – | – | – | – | – | |
3 | – | – | – | – | – | – | |
K | 1 | – | – | – | – | – | – |
2 | – | – | – | – | – | – | |
3 | – | – | – | – | – | – | |
N | 1 | – | – | – | – | – | – |
2 | – | – | – | – | – | – | |
S | 1 | 805 | 660 | 510 | 805 | 660 | 510 |
2 | 805 | 660 | 510 | 805 | 660 | 510 | |
3 | 1170 | 950 | 730 | 1170 | 950 | 730 | |
4 | – | – | – | – | – | – | |
H | 1 | – | – | – | – | – | – |
2 | – | – | – | – | – | – | |
3 | – | – | – | – | – | – |