Wróć
Edytuj
Dodaj
Nazwa : {{SolutionName}}
Frezy KNS® do frezowania rowków • Mocowanie nasadzane • Metryczne
Frezy KNS® do frezowania rowków • Mocowanie nasadzane
Właściwości i zalety
- Dwuwpustowa konstrukcja piasty do operacji wielokrotnego frezowania rowków.
- Pozytywowa geometria SGP łamacza wióra w zastosowaniach od obróbki lekkiej do ciężkiej zapewnia płynną pracę narzędzia i skuteczne odprowadzanie wiórów.
- Podwójny rowek typu V oraz gniazdo utrzymują płytkę na miejscu i minimalizują bicie promieniowe.
- Wyjątkowy mechanizm samozaciskowy zapewnia łatwą wymianę płytek.
Zastosowania
Slotting: Side
Side Milling/Shoulder Milling: Bottom Shouldering
100055043
Materiały przedmiotu obrabianego
P
Steel
M
Stainless Steel
K
Cast Iron
N
Non-Ferrous
S
High-Temp Alloys
H
Hardened Materials
Filtry i kolumny
Filters
Filtry
Filtry
Wyświetl filtry w
Metryczne
Calowe
Workpiece Material
Workpiece Material
-
P Steel (6)
-
P0Low-Carbon Steels, Long Chipping C < .25%; <125 HB; <530 N/mm^2 UTS(6)
-
P1Low-Carbon Steels, Short Chipping C < .25%; <125 HB; <530 N/mm^2 UTS(6)
-
P2Medium and High Carbon Steels C < .25%; <220 HB; <25 HRC; >530 N/mm^2 UTS(6)
-
P3Alloy Steels & Tool Steels C > .25%; <330 HB; <35 HRC; 600-850 N/mm^2 UTS(6)
-
P4Alloy Steels & Tool Steels C > .25%; 350-420 HB; 35-43 HRC; 850-1400 N/mm^2 UTS(6)
-
P5Ferritic, Martensitic, and PH Stainless Steels <330 HB; <35 HRC; 600-900 N/mm^2 UTS(6)
-
P6High Strength Ferritic, Martensitic, and PH Stainless Steels 350-450 HB; 35-43 HRC; 900-2400 N/mm^2 UTS(6)
-
-
M Stainless Steel (6)
-
M1Austenitic Stainless Steel 130-200 HB; <600 N/mm^2 UTS(6)
-
M2High Strength Austenitic Stainless and Cast Stainless Steels 150-230 HB; <25 HRC; >600 N/mm^2 UTS(6)
-
M3Duplex Stainless Steel 135-275 HB; <30 HRC; 500-1200 N/mm^2 UTS(6)
-
-
K Cast Iron (6)
-
K1Gray Cast Iron 120-290 HB; <32 HRC; 125-500 N/mm^2 UTS(6)
-
K2Low and Medium Strength CGI and Ductile Irons 130-260 HB; <28 HRC; <600 N/mm^2 UTS(6)
-
K3High Strength Ductile and Austempered Ductile Iron 180-350 HB; <43 HRC; >600 N/mm^2 UTS(6)
-
-
N Non-Ferrous Materials (6)
-
N1Wrought Aluminum(6)
-
N2Low-Silicon Aluminum Alloys and Magnesium Alloys Si <12.2%(6)
-
N3High-Silicon Aluminum Alloys Si >12.2%(6)
-
-
S High-Temp Alloys (6)
-
S1Iron-Based, Heat-Resistant Alloys 160-260 HB; 25-48 HRC; 500-1200 N/mm^2 UTS(6)
-
S2Cobalt-Based, Heat-Resistant Alloys 250-450 HB; 25-48 HRC; 1000-1450 N/mm^2 UTS(6)
-
S3Nickel-Based, Heat Resistant Alloys 160-450 HB; <48 HRC; 600-1700 N/mm^2 UTS(6)
-
S4Titanium and Titanium Alloys 300-400 HB; 33-43 HRC; 900-1600 N/mm^2 UTS(6)
-
-
H Hardened Materials (6)
-
H1Hardened Materials 44-48 HRC(6)
-
Applications
Applications
-
Slot Milling (6)
-
Slot Side (6)
-
Slot Square End (6)
Cutting Diameter
Cutting Diameter
-
3.938 in (2)
-
4.921 in (4)
do
Cutting Diameter
Cutting Diameter
-
100.0 mm (2)
-
125.0 mm (4)
do
Reach
Reach
-
2.0 in (1)
-
2.011 in (1)
-
2.415 in (1)
-
2.43 in (1)
-
2.445 in (1)
-
2.463 in (1)
do
Reach
Reach
-
50.801 mm (1)
-
51.051 mm (1)
-
61.35 mm (1)
-
61.7 mm (1)
-
62.1 mm (1)
-
62.551 mm (1)
do
Number of Flutes
Number of Flutes
-
6 (1)
-
7 (3)
-
8 (2)
Cutting Edges Per Insert
Cutting Edges Per Insert
-
1.0 (6)
-
2.0 (5)
do
Corner Radius
Corner Radius
-
0.006 in (1)
-
0.008 in (4)
-
0.012 in (2)
-
0.016 in (1)
-
0.06 in (1)
-
0.063 in (1)
-
0.079 in (1)
do
Corner Radius
Corner Radius
-
0.151 mm (1)
-
0.2 mm (4)
-
0.301 mm (2)
-
0.4 mm (1)
-
1.5 mm (1)
-
1.6 mm (1)
-
2.0 mm (1)
do
application
Grade Of Cutting Tool
Grade Of Cutting Tool
-
KC522M (6)
-
KCPK30 (6)
-
KCPM40 (6)
-
KCU25 (6)
frontEnd
Cutting Width
Cutting Width
-
0.079 in (1)
-
0.088 in (1)
-
0.095 in (1)
-
0.098 in (1)
-
0.119 in (1)
-
0.125 in (1)
-
0.157 in (1)
-
0.188 in (1)
-
0.197 in (1)
-
0.237 in (1)
-
0.25 in (1)
do
Cutting Width
Cutting Width
-
2.0 mm (1)
-
2.2 mm (1)
-
2.401 mm (1)
-
2.5 mm (1)
-
3.0 mm (1)
-
3.176 mm (1)
-
4.0 mm (1)
-
4.775 mm (1)
-
5.0 mm (1)
-
6.0 mm (1)
-
6.351 mm (1)
do
Maximum Cutting Depth
Maximum Cutting Depth
-
0.972 in (3)
-
1.012 in (2)
-
1.051 in (1)
do
Maximum Cutting Depth
Maximum Cutting Depth
-
24.701 mm (3)
-
25.701 mm (2)
-
26.701 mm (1)
do
Maximum Cutting Insert Depth
Maximum Cutting Insert Depth
-
9.175 mm (1)
-
11.55 mm (1)
-
12.675 mm (1)
-
12.75 mm (1)
-
14.5 mm (1)
-
14.525 mm (1)
-
14.75 mm (1)
do
Maximum Cutting Insert Depth
Maximum Cutting Insert Depth
-
0.361 in (1)
-
0.455 in (1)
-
0.499 in (1)
-
0.502 in (1)
-
0.572 in (1)
-
0.573 in (1)
-
0.581 in (1)
do
backEnd
Back-End Diameter
Back-End Diameter
-
22.0 mm (2)
-
32.0 mm (4)
do
Back-End Diameter
Back-End Diameter
-
0.866 in (2)
-
1.26 in (4)
do
No filters matching ""
Zmień widoczne kolumny za pomocą dowolnego z parametrów wymienionych poniżej. Można wyświetlić maksymalnie 7 kolumn.
Wyświetlanie
1- 6
z 6 Wyniki
Metryczne
Calowe
Pokaż
Metryczne
Calowe
| SAP Material Number | ISO Catalog Number | ANSI Catalog Number | Insert Size [SSC] | [D1] Effective Cutting Diameter | [D1] Effective Cutting Diameter | [CDX] Radial Maximum Depth of Cut | [CDX] Radial Maximum Depth of Cut | [D] Adapter / Shank / Bore Diameter | [D] Adapter / Shank / Bore Diameter | [D6] Hub Diameter | [D6] Hub Diameter | [L1] Gage Length | [L1] Gage Length | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 5614853 | KNSM100R07X21S022 | KNSM100R07X21S022 | 21 | 100.0000 | 3.937 | 24.7000 | .9720 | 22.0 | .87 | 49.0000 | 1.929 | 51.0500 | 2.077 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Cena katalogowa:
$2,652.80
/każdy
Twoja cena::
Ilość
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5614852 | KNSM100R08X16S022 | KNSM100R08X16S022 | 16 | 100.0000 | 3.937 | 24.7000 | .9720 | 22.0 | .87 | 49.0000 | 1.929 | 50.8000 | 2.005 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Cena katalogowa:
$2,355.17
/każdy
Twoja cena::
Ilość
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5614857 | KNSM125R06X51S032 | KNSM125R06X51S032 | 51 | 125.0000 | 4.921 | 25.7000 | 1.012 | 32.0 | 1.26 | 72.0000 | 2.835 | 62.5500 | 2.480 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Cena katalogowa:
$2,613.99
/każdy
Twoja cena::
Ilość
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5614855 | KNSM125R07X34S032 | KNSM125R07X34S032 | 34 | 125.0000 | 4.921 | 25.7000 | 1.012 | 32.0 | 1.26 | 72.0000 | 2.835 | 61.7000 | 2.440 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Cena katalogowa:
$2,458.70
/każdy
Twoja cena::
Ilość
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5614856 | KNSM125R07X42S032 | KNSM125R07X42S032 | 42 | 125.0000 | 4.921 | 26.7000 | 1.051 | 32.0 | 1.26 | 70.0000 | 2.756 | 62.1000 | 2.458 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Cena katalogowa:
$2,264.59
/każdy
Twoja cena::
Ilość
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5614854 | KNSM125R08X27S032 | KNSM125R08X27S032 | 27 | 125.0000 | 4.921 | 24.7000 | .9720 | 32.0 | 1.26 | 74.0000 | 2.913 | 61.3500 | 2.424 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Cena katalogowa:
$2,782.20
/każdy
Twoja cena::
Ilość
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Cena katalogowa:
Rabat: %
Pracownik zastępczy
Ten produkt jest niedostępny
Produkt zastępczy Ten produkt może być dostępny u dystrybutora
Produkt zastępczy Ten produkt może być dostępny u dystrybutora
Ilość
Sprzedawane w opakowaniach po
| Material Group | Light Machining | General Purpose | Heavy Machining | |||
| (Light geometry) | (Strong geometry) | |||||
| wear resistance |  <="" td=""> | toughness | ||||
| Geometry | Grade | Geometry | Grade | Geometry | Grade | |
| P1–P2 | .S..GP | KCU25 | .S..GP | KCU25 | .S..GP | KCPM40 |
| P3–P4 | .S..GP | KCU25 | .S..GP | KCU25 | .S..GP | KCPM40 |
| P5–P6 | .S..GP | KCU25 | .S..GP | KCU25 | .S..GP | KCPM40 |
| M1–M2 | .S..GP | KCU25 | .S..GP | KCPM40 | .S..GP | KCPM40 |
| M3 | .S..GP | KCU25 | .S..GP | KCPM40 | .S..GP | KCPM40 |
| K1–K2 | .S..GP | KCU25 | .S..GP | KCPK30 | .S..GP | KCPK30 |
| K3 | .S..GP | KCU25 | .S..GP | KCPK30 | .S..GP | KCPK30 |
| N1–N2 | .S..GP | KCU25 | ||||
| N3 | .S..GP | KCU25 | ||||
| S1–S2 | .S..GP | KCU25 | .S..GP | KCU25 | .S..GP | KCU25 |
| S3 | .S..GP | KCU25 | .S..GP | KCU25 | .S..GP | KCU25 |
| S4 | .S..GP | KCU25 | .S..GP | KCU25 | .S..GP | KCU25 |
Zalecane wyjściowe wartości posuwu [mm]
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | |||||||||||
| 5% | 10% | 20% | 30% | ||||||||||
| .S..GP | 0,13 | 0,28 | 0,35 | 0,09 | 0,20 | 0,32 | 0,07 | 0,15 | 0,32 | 0,06 | 0,12 | 0,30 | .S..GP |
| Light Machining | General Purpose | Heavy Machining |
Recommended Starting Feeds [IPT]
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | |||||||||||
| 5% | 10% | 20% | 30% | ||||||||||
| .S..GP | .005 | .011 | .027 | .004 | .008 | .020 | .003 | .006 | .015 | .002 | .005 | .012 | .S..GP |
| Light Machining | General Purpose | Heavy Machining |
Zalecane wyjściowe wartości prędkości skrawania [m/min]
| Material Group | KCPK30 | KCPM40 | KCU25 | |||||||
| P | 1 | 365 | 320 | 270 | 200 | 190 | 150 | 260 | 230 | 215 |
| 2 | 280 | 255 | 230 | 190 | 175 | 140 | 220 | 190 | 160 | |
| 3 | 255 | 230 | 205 | 170 | 145 | 120 | 200 | 170 | 140 | |
| 4 | 190 | 175 | 160 | 150 | 130 | 90 | 180 | 150 | 120 | |
| 5 | 260 | 230 | 210 | 105 | 75 | 60 | 150 | 135 | 120 | |
| 6 | 160 | 135 | 120 | 75 | 60 | 50 | 130 | 100 | 80 | |
| M | 1 | – | – | – | 170 | 150 | 135 | 210 | 170 | 135 |
| 2 | – | – | – | 155 | 130 | 110 | 170 | 150 | 110 | |
| 3 | – | – | – | 115 | 100 | 80 | 130 | 120 | 85 | |
| K | 1 | 260 | 230 | 205 | – | – | – | 270 | 220 | 170 |
| 2 | 235 | 210 | 190 | – | – | – | 230 | 190 | 160 | |
| 3 | 195 | 175 | 160 | – | – | – | 210 | 160 | 140 | |
| N | 1 | – | – | – | – | – | – | 760 | 680 | 400 |
| 2 | – | – | – | – | – | – | 710 | 550 | 350 | |
| 3 | – | – | – | – | – | – | 620 | 490 | 320 | |
| S | 1 | – | – | – | 30 | 25 | 25 | 30 | 25 | 20 |
| 2 | – | – | – | 30 | 25 | 25 | 30 | 25 | 20 | |
| 3 | – | – | – | 40 | 30 | 25 | 40 | 30 | 20 | |
| 4 | – | – | – | 50 | 40 | 25 | 55 | 40 | 25 | |
Recommended Starting Speeds [SFM]
| Material Group | KCPK30 | KCPM40 | KCU25 | |||||||
| P | 1 | 1200 | 1050 | 890 | 660 | 620 | 500 | 860 | 750 | 700 |
| 2 | 920 | 835 | 755 | 620 | 580 | 460 | 720 | 630 | 530 | |
| 3 | 835 | 755 | 675 | 550 | 480 | 390 | 660 | 560 | 460 | |
| 4 | 625 | 575 | 525 | 490 | 420 | 300 | 590 | 490 | 390 | |
| 5 | 855 | 755 | 690 | 350 | 250 | 200 | 490 | 440 | 390 | |
| 6 | 525 | 445 | 400 | 250 | 200 | 160 | 430 | 330 | 260 | |
| M | 1 | – | – | – | 560 | 490 | 450 | 690 | 560 | 450 |
| 2 | – | – | – | 510 | 430 | 360 | 560 | 500 | 360 | |
| 3 | – | – | – | 380 | 330 | 260 | 430 | 400 | 280 | |
| K | 1 | 850 | 760 | 665 | – | – | – | 890 | 720 | 560 |
| 2 | 770 | 690 | 630 | – | – | – | 760 | 630 | 530 | |
| 3 | 645 | 575 | 530 | – | – | – | 690 | 530 | 460 | |
| N | 1 | – | – | – | – | – | – | 2500 | 2230 | 1310 |
| 2 | – | – | – | – | – | – | 2330 | 1800 | 1150 | |
| 3 | – | – | – | – | – | – | 2030 | 1600 | 1050 | |
| S | 1 | – | – | – | – | – | – | 100 | 85 | 60 |
| 2 | – | – | – | – | – | – | 100 | 85 | 60 | |
| 3 | – | – | – | – | – | – | 125 | 100 | 60 | |
| 4 | – | – | – | – | – | – | 175 | 125 | 85 | |