Hoş Geldiniz
Lütfen tercihlerinizi onaylayın
Tercihleri Güncelle
Ürün Önerileri
Product Family suggestions
Merhaba, User Name
Seçtiğiniz Hesap:
There is an issue with your account. Please contact customer support.
Sold To Account
Hesabı Değiştir
Ship To Account
Hesabı Değiştir
- Kontrol Paneli
- Siparişleri Yönet
- Kanalları Yönet
- Adres Defteri
-
Bildirimler
Tümünü okundu olarak işaretle - Sık Kullanılanlar
- Parolayı Değiştir
- Profilim
- Oturumu Kapat
Ürün(ler)
sepete başarıyla eklendi
Sepeti Görüntüle
Sepeti Görüntüle
Limitli süre geçerli olan tekliflerimizle az ödeyip, daha çok frezeleyin.
Şimdi Satın Alın.
Ürün(ler)
sepete başarıyla eklendi
Sepeti Görüntüle
Sepeti Görüntüle
Editing Solution
Adding Solution
Solution Name: {{SolutionName}}- Ürünler
- /
- A2™ • Kesme genişliği • 4mm • Metrik
Sending to SolidCAM in progress...
Downloaded file will be available after import in the SolidCAM tool library.
A2™ • Kesme genişliği • 4mm • Metrik
Çok dar kanal açma frezeleri
Özellikler ve avantajlar
- Pozitif talaş şekillendirme özellikli kesici uçları standarttır.
- Sabit tamponlu kendinden bağlamalı kesici uç yatağı.
- Tüm düz tabanlı kanal açma ve kesme işlemleri için mükemmeldir.
- Her freze gövdesi için iki sürücü halka gerekir (ayrıca, çift olarak sipariş verilmelidir).
Kullanım ve uygulama alanları
- Slotting: Side
KVNS™ A2™ Slotting Cutters • Insert Selection Guide | ||||||
Material Group | Light
|
General
|
Heavy
|
|||
– | (Light geometry) | (Strong geometry) | ||||
– | wear
|
<="" td=""> | toughness | |||
– | Geometry | Grade | Geometry | Grade | Geometry | Grade |
P1-P2 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
P3-P4 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
P5-P6 | .S..GD | KCPK30 | .S..GB | KCPK30 | .S..GB | KCPK30 |
M1-M2 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
M3 | .S..GD | KCPK30 | .S..GB | KCPK30 | .S..GB | KCPK30 |
K1-K2 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
K3 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
N1-N2 | – | – | – | – | – | – |
N3 | – | – | – | – | – | – |
S1-S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | – | – | – | – | – | – |
H1 | – | – | – | – | – | – |
Önerilen başlangıç ilerlemeleri [mm]
KVNS™ A2™ Series • Recommended Starting Feeds [mm/th] | |||||||||||||||
Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | ||||||||||||||
5% | 10% | 20% | 30% | 40–100% | |||||||||||
L | M | H | L | M | H | L | M | H | L | M | H | L | M | H | |
.S..GD | 0,23 | 0,46 | 0,71 | 0,17 | 0,33 | 0,51 | 0,13 | 0,25 | 0,38 | 0,11 | 0,22 | 0,33 | 0,10 | 0,20 | 0,30 |
.S..GB | 0,23 | 0,46 | 0,74 | 0,17 | 0,33 | 0,54 | 0,13 | 0,25 | 0,40 | 0,11 | 0,22 | 0,35 | 0,10 | 0,20 | 0,32 |
L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use "Light Machining" values as starting feed rate. |
Light
|
General
|
Heavy
|
Recommended Starting Feeds [IPT]
KVNS™ A2™ Series • Recommended Starting Feeds [IPT] | |||||||||||||||
Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | ||||||||||||||
5% | 10% | 20% | 30% | 40–100% | |||||||||||
L | M | H | L | M | H | L | M | H | L | M | H | L | M | H | |
.S..GD | 0.009 | 0.017 | 0.026 | 0.007 | 0.013 | 0.019 | 0.005 | 0.009 | 0.014 | 0.004 | 0.008 | 0.012 | 0.004 | 0.008 | 0.011 |
.S..GB | 0.009 | 0.017 | 0.028 | 0.007 | 0.013 | 0.020 | 0.005 | 0.009 | 0.015 | 0.004 | 0.008 | 0.013 | 0.004 | 0.008 | 0.012 |
L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use "Light Machining" values as starting feed rate. |
Light
|
General
|
Heavy
|
Önerilen Başlangıç Hızları [m/dak]
KVNS™ A2™ Series • Recommended Starting Speed [m/min] | |||||||
Grade | KCPK30 | KMF | |||||
Chip Thickness hex mm | Min | Max | Min | Max | |||
Material Group | Max | Start | Min | Max | Start | Min | |
P | 1 | 455 | 395 | 370 | – | – | – |
2 | 280 | 255 | 230 | – | – | – | |
3 | 255 | 230 | 205 | – | – | – | |
4 | 225 | 185 | 160 | – | – | – | |
5 | 190 | 170 | 150 | – | – | – | |
6 | 160 | 135 | 110 | – | – | – | |
M | 1 | 205 | 185 | 155 | – | – | – |
2 | 185 | 160 | 140 | – | – | – | |
3 | 145 | 130 | 115 | – | – | – | |
K | 1 | 295 | 265 | 240 | – | – | – |
2 | 235 | 210 | 190 | – | – | – | |
3 | 195 | 175 | 160 | – | – | – | |
N | 1 | – | – | – | 335 | 298 | 271 |
2 | – | – | – | 335 | 298 | 271 | |
3 | – | – | – | 219 | 198 | 170 | |
S | 1 | – | – | – | 30 | 24 | 20 |
2 | – | – | – | 30 | 24 | 20 | |
3 | – | – | – | 30 | 24 | 20 | |
4 | 50 | 45 | 35 | 24 | 24 | 24 | |
H | 1 | – | – | – | – | – | – |
Recommended Starting Speed are pointing to 90° Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. |
Recommended Starting Speeds [SFM]
KVNS™ A2™ Series • Recommended Starting Speed [SFM] | |||||||
Grade | KCPK30 | KMF | |||||
Chip Thickness hex Inch | Min | Max | Min | Max | |||
Material Group | Max | Start | Min | Max | Start | Min | |
P | 1 | 1495 | 1295 | 1215 | – | – | – |
2 | 920 | 835 | 755 | – | – | – | |
3 | 835 | 755 | 675 | – | – | – | |
4 | 740 | 605 | 525 | – | – | – | |
5 | 625 | 560 | 490 | – | – | – | |
6 | 525 | 445 | 360 | – | – | – | |
M | 1 | 675 | 605 | 510 | – | – | – |
2 | 605 | 525 | 460 | – | – | – | |
3 | 475 | 425 | 375 | – | – | – | |
K | 1 | 970 | 870 | 785 | – | – | – |
2 | 770 | 690 | 625 | – | – | – | |
3 | 640 | 575 | 525 | – | – | – | |
N | 1 | – | – | – | 1100 | 980 | 890 |
2 | – | – | – | 1100 | 980 | 890 | |
3 | – | – | – | 720 | 650 | 560 | |
S | 1 | – | – | – | 100 | 80 | 65 |
2 | – | – | – | 100 | 80 | 65 | |
3 | – | – | – | 100 | 80 | 65 | |
4 | 165 | 150 | 115 | 80 | 80 | 80 | |
H | 1 | – | – | – | – | – | – |
Recommended Starting Speed are pointing to 90° Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. |