KSEM PLUS™ • Plaquette extérieure • Géométrie DFC-MD
Perçage modulaire • Plaquette carbure pour têtes KSEM PLUS™ B1
Features and benefits
- Plaquette de perçage pour une application principale dans les aciers inoxydables.
- Les plaquettes DFC assurent un guidage latéral et une bonne qualité de perçage
- Deux arêtes de coupe.
Workpiece Materials
P
Steel
M
Stainless Steel
K
Cast Iron
N
Non-Ferrous
S
High-Temp Alloys
Filters and Columns
Filters
Filters
Filters
View filters in
Metric
Inch
Workpiece Material
Workpiece Material
-
P Steel (5)
-
P0Low-Carbon Steels, Long Chipping C < .25%; <125 HB; <530 N/mm^2 UTS(5)
-
P1Low-Carbon Steels, Short Chipping C < .25%; <125 HB; <530 N/mm^2 UTS(5)
-
P2Medium and High Carbon Steels C < .25%; <220 HB; <25 HRC; >530 N/mm^2 UTS(5)
-
P3Alloy Steels & Tool Steels C > .25%; <330 HB; <35 HRC; 600-850 N/mm^2 UTS(5)
-
P4Alloy Steels & Tool Steels C > .25%; 350-420 HB; 35-43 HRC; 850-1400 N/mm^2 UTS(5)
-
P5Ferritic, Martensitic, and PH Stainless Steels <330 HB; <35 HRC; 600-900 N/mm^2 UTS(5)
-
P6High Strength Ferritic, Martensitic, and PH Stainless Steels 350-450 HB; 35-43 HRC; 900-2400 N/mm^2 UTS(5)
-
-
M Stainless Steel (5)
-
M1Austenitic Stainless Steel 130-200 HB; <600 N/mm^2 UTS(5)
-
M2High Strength Austenitic Stainless and Cast Stainless Steels 150-230 HB; <25 HRC; >600 N/mm^2 UTS(5)
-
M3Duplex Stainless Steel 135-275 HB; <30 HRC; 500-1200 N/mm^2 UTS(5)
-
-
K Cast Iron (5)
-
K1Gray Cast Iron 120-290 HB; <32 HRC; 125-500 N/mm^2 UTS(5)
-
K2Low and Medium Strength CGI and Ductile Irons 130-260 HB; <28 HRC; <600 N/mm^2 UTS(5)
-
K3High Strength Ductile and Austempered Ductile Iron 180-350 HB; <43 HRC; >600 N/mm^2 UTS(5)
-
-
N Non-Ferrous Materials (5)
-
N1Wrought Aluminum(5)
-
N2Low-Silicon Aluminum Alloys and Magnesium Alloys Si <12.2%(5)
-
N3High-Silicon Aluminum Alloys Si >12.2%(5)
-
N4Copper, Brass, Zinc-based on machinability index range of 70-100(5)
-
N5Nylon, Plastics, Rubbers, Phenolics, Resins, Fiberglass(5)
-
N6Carbon, Graphite Composites, CFRP(5)
-
N7MMC's(5)
-
-
S High-Temp Alloys (5)
-
S1Iron-Based, Heat-Resistant Alloys 160-260 HB; 25-48 HRC; 500-1200 N/mm^2 UTS(5)
-
S2Cobalt-Based, Heat-Resistant Alloys 250-450 HB; 25-48 HRC; 1000-1450 N/mm^2 UTS(5)
-
S3Nickel-Based, Heat Resistant Alloys 160-450 HB; <48 HRC; 600-1700 N/mm^2 UTS(5)
-
S4Titanium and Titanium Alloys 300-400 HB; 33-43 HRC; 900-1600 N/mm^2 UTS(5)
-
Select First Choice
-
CN (5)
-
DE (5)
-
GB (2)
-
IN (2)
-
SG (5)
-
US (5)
Cutting Condition
Cutting Condition
-
Interrupted (5)
-
Stable (5)
-
Unstable (5)
Corner Radius
Corner Radius
-
0.0397 in (1)
-
0.047 in (1)
-
0.0476 in (1)
-
0.063 in (1)
-
0.079 in (1)
to
Corner Radius
Corner Radius
-
1.0 mm (1)
-
1.2 mm (2)
-
1.6 mm (1)
-
2.0 mm (1)
to
application
Drilling Condition
Drilling Condition
-
Interrupted (5)
-
Stable (5)
-
Unstable (5)
No filters matching ""
Change the visible columns with any of the parameters listed below. A maximum of 7 columns can be displayed.
Displaying
1- 5
of 5 results
Metric
Inch
Show
Metric
Inch
| SAP Material Number | ISO Catalog Number | ANSI Catalog Number | Grade | First Choice | [LI] Insert Length | [LI] Insert Length | [W] Insert Width | [W] Insert Width | [D1] Insert Hole Size | [D1] Insert Hole Size | [S] Insert Thickness | [S] Insert Thickness | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 5118457 | DFC040310D28MD | DFC040310D28MD | KC7140 | 10.0000 | .3937 | 7.6000 | .2990 | 2.8500 | .1122 | 3.1800 | .1250 | 1.0000 | .0397 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$20.40
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5118458 | DFC05T312D32MD | DFC05T312D32MD | KC7140 | 12.0000 | .4724 | 9.4000 | .3700 | 3.4000 | .1339 | 3.7500 | .1476 | 1.2000 | .0476 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$20.40
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5118459 | DFC06T312D36MD | DFC06T312D36MD | KC7140 | 16.0000 | .6300 | 12.4000 | .4880 | 4.4000 | .1730 | 3.7500 | .1480 | 1.2000 | .0470 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$23.05
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5118460 | DFC070416D45MD | DFC070416D45MD | KC7140 | 18.0000 | .7087 | 14.5000 | .5710 | 4.4000 | .1732 | 4.7500 | .1870 | 1.6000 | .0630 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$27.64
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5118461 | DFC090520D56MD | DFC090520D56MD | KC7140 | 24.0000 | .9449 | 19.0000 | .7480 | 5.5000 | .2165 | 5.2500 | .2070 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
List price:
$32.44
/each.
Your price::
Qty
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
List price:
Discount: %
Replacement
This item is not available
Replacement Product This item may be available through a distributor
Replacement Product This item may be available through a distributor
Qty
Sold in pkg. of
Grades
-
KC7140
Composition : Carbure à grain moyen avec revêtement TiCN/TiN PVD d'une grande ténacité.
Application : Convient pour l'usinage de l'acier et de l'acier inoxydable. Cette nuance d'une ténacité exceptionnelle, qui offre une excellente tenue de coupe, est parfaite en conditions d'usinage peu stables.P SteelS High-Temp AlloysK Cast IronM Stainless SteelN Non-Ferrous
| D1 | tolerance h8 + / - |
| 12,5–18 | +0,000/-0,027 |
| 18–30 | +0,000/-0,033 |
| 30–40 | +0,000/-0,039 |
| D1 | tolerance h8 + / - |
| .500–.709 | +.000/-.0010 |
| .709–1.181 | +.000/-.0013 |
| 1.181–1.575 | +.000/-.0015 |
| Metric | |||||||||||
| Material Group | Condition | Cutting Speed vc | Recommended Feed Rate (fz) by Diameter | ||||||||
| Range m/min | |||||||||||
| min | Starting Value | max | Ø | KSEM 14….17 DFR/DFC04... 28.0031,74 | KSEM 15….18 DFT/DFC05… 31,7435,99 | KSEM 13….22 DFT/DFC06... 36,0044,99 | KSEM 18….28 DFT/DFC07... 45,0055,99 | KSEM 20….34 DFT/DFC09... 56,0070 | |||
| P | 1 | S | 115 | 235 | 290 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 |
| U | 90 | 160 | 215 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 65 | 100 | 140 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| 2 | S | 90 | 190 | 230 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,360 | 0,200–0,400 | 0,200–0,450 | |
| U | 71 | 130 | 170 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,360 | 0,200–0,400 | 0,200–0,450 | ||
| I | 50 | 80 | 110 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| 3 | S | 90 | 180 | 230 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | |
| U | 70 | 120 | 170 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| I | 50 | 70 | 106 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| 4 | S | 90 | 140 | 220 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | |
| U | 70 | 110 | 160 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| I | 50 | 80 | 110 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| 5 | S | 90 | 130 | 210 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | |
| U | 70 | 100 | 150 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| I | 50 | 70 | 100 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| 6 | S | 70 | 90 | 180 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | |
| U | 50 | 75 | 120 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| I | 40 | 60 | 100 | mm/r | 0,160–0,280 | 0,160–0,280 | 0,200–0,320 | 0,200–0,400 | 0,200–0,450 | ||
| M | 1 | S | 60 | 110 | 135 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 |
| U | 40 | 70 | 90 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 30 | 50 | 65 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| 2 | S | 60 | 100 | 135 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | |
| U | 40 | 60 | 90 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 30 | 50 | 65 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| 3 | S | 50 | 90 | 135 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | |
| U | 40 | 60 | 90 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 25 | 40 | 65 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| K | 1 | S | 90 | 170 | 230 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 |
| U | 60 | 120 | 160 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | ||
| I | 40 | 70 | 90 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | ||
| 2 | S | 90 | 160 | 220 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | |
| U | 60 | 110 | 160 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | ||
| I | 40 | 70 | 100 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | ||
| 3 | S | 90 | 150 | 210 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | |
| U | 60 | 100 | 150 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | ||
| I | 35 | 60 | 90 | mm/r | 0,180–0,300 | 0,180–0,300 | 0,216–0,360 | 0,240–0,420 | 0,300–0,480 | ||
| N | 1 | S | 150 | 240 | 360 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 |
| U | 100 | 160 | 240 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 60 | 100 | 160 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| 2 | S | 150 | 220 | 360 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | |
| U | 100 | 150 | 240 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 60 | 100 | 160 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| 3 | S | 150 | 200 | 360 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | |
| U | 100 | 140 | 240 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 60 | 90 | 160 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| 4 | S | 150 | 200 | 360 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | |
| U | 100 | 140 | 240 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 60 | 90 | 160 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| 5 | S | 150 | 200 | 360 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | |
| U | 100 | 140 | 240 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 60 | 90 | 160 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| 6 | S | 150 | 200 | 360 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | |
| U | 100 | 140 | 240 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 60 | 90 | 160 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| 7 | S | 110 | 220 | 260 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | |
| U | 70 | 140 | 170 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| I | 45 | 90 | 110 | mm/r | 0,120–0,200 | 0,120–0,200 | 0,144–0,280 | 0,160–0,320 | 0,200–0,400 | ||
| S | 1 | S | 25 | 50 | 75 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 |
| U | 20 | 40 | 60 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 15 | 30 | 50 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| 2 | S | 20 | 40 | 60 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | |
| U | 15 | 30 | 45 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 12 | 25 | 35 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| 3 | S | 20 | 40 | 60 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | |
| U | 15 | 30 | 45 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 12 | 25 | 40 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| 4 | S | 20 | 40 | 60 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | |
| U | 15 | 30 | 45 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| I | 12 | 25 | 40 | mm/r | 0,130–0,250 | 0,130–0,250 | 0,160–0,280 | 0,160–0,320 | 0,200–0,360 | ||
| Inch | |||||||||||
| Material Group | Condition | Cutting Speed vc | Recommended Feed Rate (fz) by Diameter | ||||||||
| Range SFM | |||||||||||
| min | Starting Value | max | Ø | KSEM 14….17 DFR/DFC04... 1.1021.249 | KSEM 15….18 DFT/DFC05… 1.2501.416 | KSEM 13….22 DFT/DFC06... 1.4171.771 | KSEM 18….28 DFT/DFC07... 1.7722.204 | KSEM 20….34 DFT/DFC09... 2.2054.0295 | |||
| P | 1 | S | 370 | 775 | 944 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 |
| U | 290 | 532 | 698 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 205 | 327 | 451 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| 2 | S | 295 | 623 | 755 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | |
| U | 233 | 427 | 558 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| I | 164 | 262 | 361 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| 3 | S | 295 | 591 | 755 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | |
| U | 230 | 394 | 558 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| I | 164 | 230 | 361 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| 4 | S | 295 | 459 | 722 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | |
| U | 230 | 361 | 525 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| I | 264 | 262 | 361 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| 5 | S | 295 | 427 | 689 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | |
| U | 230 | 328 | 689 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| I | 164 | 230 | 492 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| 6 | S | 230 | 295 | 591 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | |
| U | 164 | 246 | 394 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| I | 131 | 197 | 328 | IPR | 0.006–0.011 | 0.006–0.011 | 0.008–0.014 | 0.008–0.016 | 0.008–0.018 | ||
| M | 1 | S | 197 | 361 | 443 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 |
| U | 131 | 230 | 295 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 98 | 164 | 213 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| 2 | S | 197 | 328 | 443 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | |
| U | 131 | 197 | 295 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 98 | 164 | 213 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| 3 | S | 164 | 295 | 443 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | |
| U | 131 | 197 | 295 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 82 | 131 | 213 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| K | 1 | S | 295 | 558 | 755 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 |
| U | 197 | 394 | 525 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | ||
| I | 131 | 230 | 295 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | ||
| 2 | S | 295 | 525 | 722 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | |
| U | 197 | 361 | 525 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | ||
| I | 131 | 230 | 328 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | ||
| 3 | S | 295 | 492 | 689 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | |
| U | 197 | 328 | 492 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | ||
| I | 115 | 197 | 295 | IPR | 0.007–0.012 | 0.007–0.012 | 0.009–0.014 | 0.009–0.017 | 0.012–0.019 | ||
| N | 1 | S | 492 | 787 | 1181 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 |
| U | 328 | 525 | 787 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 197 | 328 | 525 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| 2 | S | 492 | 722 | 1181 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | |
| U | 328 | 492 | 787 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 197 | 328 | 525 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| 3 | S | 492 | 722 | 1181 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | |
| U | 328 | 492 | 787 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 197 | 328 | 525 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| 4 | S | 492 | 722 | 1181 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | |
| U | 328 | 492 | 787 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 197 | 328 | 525 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| 5 | S | 492 | 722 | 1181 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | |
| U | 328 | 492 | 787 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 197 | 328 | 525 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| 6 | S | 492 | 656 | 1181 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | |
| U | 328 | 459 | 787 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 197 | 295 | 525 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| 7 | S | 361 | 722 | 853 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | |
| U | 230 | 459 | 558 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| I | 148 | 295 | 361 | IPR | 0.005–0.008 | 0.005–0.008 | 0.006–0.011 | 0.006–0.013 | 0.008–0.016 | ||
| S | 1 | S | 82 | 164 | 246 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 |
| U | 66 | 131 | 197 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 49 | 98 | 164 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| 2 | S | 66 | 131 | 197 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | |
| U | 49 | 98 | 148 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 39 | 82 | 115 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| 3 | S | 66 | 131 | 197 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | |
| U | 49 | 98 | 148 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 39 | 82 | 131 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| 4 | S | 66 | 131 | 197 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | |
| U | 49 | 98 | 148 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
| I | 39 | 82 | 131 | IPR | 0.005–0.010 | 0.005–0.010 | 0.006–0.011 | 0.006–0.013 | 0.008–0.014 | ||
Carrières
✉ Gardons le contact
© 2022 Terms & Conditions of Use | Conditions of Sale | Data Privacy Policy
Kennametal Inc. 525 William Penn Place Suite 3300, Pittsburgh, PA 15219
